Barcode scanner IDM160 via RS-422

Vorheriges Oben Nächstes Helps selection copy topic address english version

HMIs, human machine interfacesET-208Electrical Installation ET-208Connection ofReadersBarcode scanner IDM160 via RS-422

 

Handheld scanner:

The wired handheld scanner is connected to the VB-IDM160-XX6-RS232-SR-* connection cable by inserting the RJ45 plug into the corresponding socket until you can hear a "click". Then check that the cable is firmly connected.

 

Fgr_Hand_Scanner_IDM160

 

Pin assignment:

 

 

Cable to scanner

Device name

Binder plug

Cable

Position

3

4

Definition

VB-IDM160-XX6-RS232-SR-...

View

Fgr_Plug_3_PE

Assignments / connections (wire / pin)

Pin

Signal

1

+UB

2

GND

3

TxD

4

-

-

-

 

Bluetooth base station:

Hinweis

Before screwing the base loading station onto the (field) enclosure, the VB-IDM160-Base-RSi-RS232-SR-*.8m-Z1 connection cable must be inserted into the opening on the underside of the base loading station.

 

1.The plug must engage audibly.

2.Clamp the connection cable into the cable bushing.

 

Fgr_Wireless_Scanner_IDM160

 

Pin assignment:

 

 

Cable to scanner

Device name

Binder plug

Cable

Position

1

2

Definition

VB-IDM160-XX6-RS232-SR-...

View

Fgr_Plug_3_PE

Assignments / connections (wire / pin)

Pin

Signal

1

+UB

2

GND

3

TxD

4

-

-

-

 

To Readerbox X3:

Fgr_BinderSocket_to_ReaderBox

 

 

Connection to the flange

Device name

ReaderBox-054-DC-RS232

data circuit

Binder fixed socket

Position

1

2

Definition

open cable end X3

IDM160-Socket-3+PE

View

Fgr_ReaderBox_X3_Cable

Fgr_Socke_3_PE

Assignments / connections (wire / pin)

Wire

Signal

Pin

Signal

 

+ VDC

1

+UB

 

GND

2

GND

 

RxD

3

TxD

 

TxD *

4

-

Green / yellow

Not used **

-

-

 

*

the wire 4 of the X3 data circuit of the ReaderBox is not needed and must be cut off at the cable end !

**

This wire was cut off ex-factory and is not assigned in the ReaderBox !

When the data cable is shortened, this wire must also be cut off again.

 

Readerbox X2 to ET-/MT-208:

Inside junction box of the ET / MT-208:

ReaderBox_To_208_RS422

 

Hinweis

The X2 interface of the Readerbox

must be connected to interface X3 (COM2) of the ET/MT-208.

 

RS-422 connection detail:

 

ReaderBox_To_208_detail

 

 

Device name

ReaderBox-...-DC(AC)*1

Connection

Data circuit

Cable

5 x 1 mm²

-

Designation

Open cable end X2

Terminal X3 (COM2 - RS-422)

View

Fgr_ReaderBox_X3_Cable

delivery state:

all wires black and numbered.

Fgr_EXe_Terminal

Assignments / connections

(wire / pin)

Wire

Signal

Pin

Signal

3


RxD-b

1

TxD-b

4


RxD-a

2

TxD-a

1


TxD-b

3

RxD-b

2


TxD-a

4

RxD-a

5

Green / Yellow

Not used

-

-

 

*1)

DC = ReaderBox with 24 VDC connection.

AC = ReaderBox with 100 to 240 VAC connection.

 

Hinweis

The blue wires of the X2 data circuit of the ReaderBox is not needed and must be cut off at the cable end !

 

The supply voltage can not be looped through the ET-208 / MT-208. Therefore you must split it in Ex-e terminal box and lead it to the devices separately.

 

Click to expand or collaps information.  24 VDC an Readerbox

 

Hinweis

The output circuit cable is about 1.1 metres long and typically 3 x 1 mm² !

 

Wire

Signal name

Definition

1

+ VDC

Supply voltage 24VDC+

2

GND

Supply voltage ground 0VDC

Green/yellow

 

Equipotential bonding

 

Click to expand or collaps information.  100 bis 240 VAC Netzspannung an Readerbox

 

Hinweis

The output circuit cable is about 1.1 metres long and typically 3 x 1 mm² !

 

Wire

Signal name

Definition

1

L1

Supply voltage phase

2

N

Supply voltage neutral

PE

Earth

Protective earth

 

Warnhinweis

Re. *1),

Make sure you have the AC version

before connecting the ReaderBox to the mains !

 

 

 

<< back